-
8 Zone Asenware Fire Alarm Control Panel
8 Zone Asenware Fire alarm control panel Specification:-
It is modularized design, the panel can expend from 1 zone to 32 zones easily.
It has 2 level control mode by a lock
It has 24VDC and 5VDC power supply output.
It has FIRE and FAULT signal output.
It has 2 general sounders output.
Each zone has 1 circuit detectors input .
Each zone can be disable by a button.
It has RESET button to reset the panel.
It has SILENCE button to stop BUZZER and SOUNDERS.
It has EVACUATE button to start a manual fire alarm immediately.
It has battery low protection function, when battery voltage lower than 21VDC, battery will be cut off automatically until the mains power is on.
It has an optional GSM module for fire alarm by SMS .KSh22,000.00KSh25,000.008 Zone Asenware Fire Alarm Control Panel
KSh22,000.00KSh25,000.00 -
Fire Alarm Sounder and Strobe Light
Fire Alarm Sounder and Strobe Light is powered by a 24v electrical circuit. In the event of a fire, the sounder will sound and flash at the same time. Very stable and reliable; easy to install and wire; can be used in different emergency situations.
- Adopt the two-wire or the four-wire system wiring method
- The mainline end receives two main lines, No polarization
- Connect the power end to a DC24V power line.
KSh1,700.00Fire Alarm Sounder and Strobe Light
KSh1,700.00 -
Asenware Battery Powered Stand Alone Smoke Detector
Asenware Battery Powered Stand Alone Smoke Detector is a photo-detector that uses the most advanced optical sensing chamber. It is designed to provide open area protection without wiring, and it is easy to install and construct.
Asenware Battery Powered Smoke Detector specifications:-
Operating Voltage:- 9VDC(with battery)
Operating Current:- Monitoring Status <= 8uA, alarm status<= 20mA Temprature:- -10 Degree Celcius ~ 55 Degree celcius Relative humidity:- <= 95% non condensing Protection class: IP20 Application: Indoor use only Smoke Alarm Sensitivity:- 0.18 to 0.26 dBM Alarm level: >= 85dB@3m and >= 93dB@1m
Materials and colors:- ABS, whiteKSh1,400.00 -
Asenware Fire Alarm Smoke Detector
Asenware Fire Alarm Smoke Detector uses a state-of-the-art optical sensing chamber. This detector is designed to provide open area protection and to be used with the most conventional fire alarm panel.
- Operating Voltage Range: 9 to 28 VDC Non-polarized
- Standby Current: ≤120uA@24VDC
- Maximum Alarm Current(LED on): ≤15mA@24VDC（1K Ohm current-limiting resistance）
- Operating Humidity Range: ≤95%RH(40℃±2℃)RelativeHumidity, Non-condensing
- Operating Temperature Range: -10℃ to 50℃(14ºF to 122ºF)
- Smoke Alarm Sensitivity: 0.1-0.15dB/m
- Height: 48.2mm installed in Base
KSh1,200.00Asenware Fire Alarm Smoke Detector
KSh1,200.00 -
Conventional Manual Call Point AW-D135C
The AW-D135C Conventional manual call point is designed to be use with an intelligent two-wire control system. If it is pressed after a fire is manually confirmed, an alarm signal may be sent to a fire alarm control system which will, after receiving the alarm signal, display the equipment status of the manual fire call points. When the manual fire call points is operating normally, the red indicator will blink; when there is a fire alarm, it will remain lit.
This passage will introduce the features, installation, wiring and use of AW-D135C conventional manual call point, to help you understand more about the conventional manual call point.
KSh999.00Conventional Manual Call Point AW-D135C
KSh999.00
